ELM327 Device

The Elm327Device provides low-level serial communication with an ELM327-compatible automotive diagnostic device. It sends raw ELM327 commands and returns Elm327Response objects.

OBD-II request modeling and PID decoding belong in protocols.obd2. An adapter that translates between those protocol models and this device belongs in controllers.automotive.

Connection

The default connection is /dev/rfcomm0 at 38400 baud. Both values can be configured when creating the device:

from hardware_io.automotive.elm327 import Elm327Device
 
 
device = Elm327Device(port="/dev/rfcomm0", baud=38400)
 
try:
    device.connect()
    response = device.send_command("ATI")
    print(response.raw)
finally:
    device.disconnect()

Initialization

On connection, the device sends ATZ, ATE0, ATL0, ATS0, ATH1, and ATSP0 to reset and configure the ELM327.

Initialization commands use a settling delay. Normal commands do not use a fixed delay; the device starts reading immediately and completes the command when it receives the ELM327 > prompt.

Dependency

The device requires pyserial:

python3 -m pip install pyserial

Bluetooth RFCOMM

A Bluetooth Classic ELM327 uses the Serial Port Profile (SPP). BlueZ exposes that connection as an RFCOMM serial device such as /dev/rfcomm0, which Elm327Device opens through pyserial.

Use the setup helper with the address reported by the Bluetooth scanner:

scripts/installers/setup_bluetooth_spp.sh \
    --address 12:34:5A:05:9C:54

The helper:

1. Checks whether the device is already paired and pairs it when needed.
2. Marks the device as trusted.
3. Disconnects any connection held by bluetoothctl.
4. Uses SDP to discover the Serial Port Profile channel.
5. Installs and starts a systemd service that actively maintains /dev/rfcomm0 now and on future boots, restarting the RFCOMM connection if it drops.
6. Warns if the current user does not belong to dialout.

Specify the channel only when SDP discovery fails:

scripts/installers/setup_bluetooth_spp.sh \
    --address 12:34:5A:05:9C:54 \
    --channel 1

The host installer can install the feature and configure RFCOMM together:

scripts/installers/host_setup.sh \
    --target rpi5 \
    --feature bluetooth \
    --feature automotive \
    --bluetooth-spp-address 12:34:5A:05:9C:54

Pairing and RFCOMM configuration are host responsibilities. Elm327Device intentionally begins at the serial-device boundary and does not invoke bluetoothctl, sdptool, or rfcomm itself.

Component Test

The component test opens a real serial connection, initializes the ELM327, and lets you send raw adapter or OBD-II commands. It does not emulate an adapter and does not decode OBD-II PID values.

Use this raw test first to separate serial, RFCOMM, and ELM327 problems from OBD-II parsing problems. Once commands such as ATI and 0100 work, use the decoded automotive component test to exercise Elm327ObdAdapter and the PID decoders.

Prerequisites

Before running the test:

1. Power the ELM327 and, for a Bluetooth model, pair it with the host.
2. Establish its RFCOMM serial device, such as /dev/rfcomm0.
3. Confirm that the device exists and that your user can access it:

ls -l /dev/rfcomm0

Serial devices are commonly assigned to the dialout group. If necessary, add your user to that group, then log out and back in:

sudo usermod -aG dialout "$USER"

Activate the project virtual environment so that pyserial and the project packages are available:

source venv/bin/activate

Interactive Mode

From the project root, run:

python3 -m hardware_io.automotive.elm327.component_test.elm327_cli

The test connects to /dev/rfcomm0 at 38400 baud by default. After the ELM327 initialization commands succeed, enter commands at the prompt:

Connecting to ELM327 on /dev/rfcomm0 at 38400 baud...
Connected. Enter an ELM327 command, or 'quit' to stop.
 
elm327> ATI
 
Command: ATI
Response:
  ELM327 v1.5
 
Raw response:
'ELM327 v1.5\r>'
elm327> quit

Useful initial commands include:

• ATI — report the adapter identification string.
• ATDP — report the selected vehicle protocol.
• 0100 — request the vehicle's supported Mode 01 PIDs.

Enter quit or exit, press Ctrl+D, or press Ctrl+C to disconnect and stop the test.

Single-Command Mode

Use --command to connect, send one command, print its response, and exit:

python3 -m hardware_io.automotive.elm327.component_test.elm327_cli \
    --command ATI

Use --port and --baud for an adapter with different serial settings:

python3 -m hardware_io.automotive.elm327.component_test.elm327_cli \
    --port /dev/ttyUSB0 \
    --baud 9600 \
    --command ATI

Display all command-line options with:

python3 -m hardware_io.automotive.elm327.component_test.elm327_cli --help

Troubleshooting

• Unable to connect usually means the serial path is wrong, RFCOMM is not connected, the user lacks device permission, or another process owns the port.
• An empty response means the serial connection opened but the adapter did not return data before the configured timeout.
• NO DATA is an ELM327 response, not a connection failure. It can mean the vehicle is off, no ECU answered, or the requested PID is unsupported.
• Some inexpensive adapters advertise an inaccurate ELM327 version string, so ATI identifies what the adapter claims rather than verifying its firmware.